New Braunfels Well Drilling (830) 555-0192

Well Pump Replacement and Repair in New Braunfels, TX

Technician servicing well system pipes and a valve fitting on a Comal County property

New Braunfels Well Drilling replaces and repairs well pumps across New Braunfels and Comal County, Texas. When the water stops or the pressure fades, the pump is the first suspect, but it is not always the culprit. A pressure switch, a waterlogged tank, a hole in the drop pipe, or a well level that dropped in a dry spell can all produce the same dead faucet. We test the whole system and fix the part that actually failed.

A submersible pump sits near the bottom of the well and pushes water up to a pressure tank in the house or well house. When it fails you lose water fast. This is year-round work, not seasonal. A pump can die in January as easily as a dry summer pulls an Edwards level down in August, and a household with no water needs it back today, not next week. Getting the diagnosis right the first time is what keeps the bill honest.

We Diagnose Before We Pull

Pulling a submersible is real work, so we do not do it until we know we have to. The pressure switch, the tank, the capacitor, and the wiring at the panel are all above ground, and a fair share of no-water calls trace to one of them. We test those first. If the fix is up top, you never pay to pull the well. If the pump or the drop pipe is the problem, then we pull it, and while the well is open we replace worn pipe and wire so the next failure is years away, not months.

Sizing the New Pump to the Well

A replacement pump is not a like-for-like swap off a shelf. The right pump matches your well depth, your water level, and how much water the household and any irrigation actually draw. On an Edwards well that swings with the seasons, it also has to sit low enough to stay under water when the level falls. Too small and the pressure sags; too large and it pulls the well down and short-cycles itself to an early grave. We match the pump to the well and set it right, so it lasts.

No water, low pressure, or a pump that will not shut off? Call (830) 555-0192.

How do I know if my well pump is failing?

The common signs are sputtering air at the faucet, pressure that will not build, a pump that runs constantly, or a breaker that keeps tripping. Sometimes it is sandy or cloudy water. Any of those can be the pump, the pressure switch, the tank, or the wiring, and in the Edwards they can also mimic a well level that dropped with a dry spell. We test the system end to end and find the actual failed part rather than swapping the whole works and hoping.

How long does a submersible pump last?

A quality submersible in a clean well commonly runs ten to fifteen years, sometimes longer. Sandy water, frequent cycling from a waterlogged pressure tank, or an undersized pump wears one out faster. When we replace a pump we look at why the old one died, because dropping an identical pump into the same conditions just buys you a repeat. Fixing the cause is cheaper than replacing the pump twice.

Do you have to pull the whole pump to fix it?

Not always. A dead pressure switch, a waterlogged tank, or a bad capacitor is an above-ground fix and needs no pulling at all. But a failed submersible, a hole in the drop pipe, or bad wiring down the well means pulling the pump. We diagnose the above-ground parts first, because if the fix is up top we save you the cost and the time of pulling the well.

My water suddenly turned cloudy after a heavy rain. Why?

In the Edwards karst, hard rain can push surface water and sediment into the aquifer fast through the fractures and recharge features, and a well can turn cloudy for a while afterward. It can also mean a pump drawing sand or a well seal letting surface water in. Because the Edwards moves water so quickly, cloudy water after a storm is worth checking rather than ignoring. We find the source and test the water.

Can you replace a pump you did not install?

Yes. Most of our pump work is on wells someone else drilled, often decades ago. We pull whatever is down there, match a new pump to your well depth and water demand, and replace worn drop pipe, wire, or fittings while the well is open, because that is the cheap time to do it. You get a well that runs and a clear picture of what is actually in the ground.

Call now for a free estimate.

(830) 555-0192

Free estimates. Mon-Sat, 8am to 6pm.

☎ Tap to Call: (830) 555-0192